Pings but no connection
Phew... I have tried everything I can think of to connect from other LAN computers to Laragon.
When I install Laragon, and then WordPress, I can access WP with no issues so long as I am on the computer where Laragon is located. However, all attempts to connect from other computers fails with "cannot connect" messages.
I have removed and reinstalled all a few times to no avail. I have dropped all firewalls and still no change. The odd thing is that I can ping to the IP addy 192.168.1.5 with no issues, but cannot even get the Laragon screen at that IP address.
I am not using Nginx and prefer to just access without it since this all on localhost. And, I have had Laragon in the past working fine, but something is obviously at work blocking things. Any suggestions and ideas solicited and appreciated.
This morning, from remote on LAN to computer with Laragon:
Ping Laragon address 192.168.1.5 Passes
Accessed server computer over LAN by computer name in Windows Explorer Passes - Displayed&Accessed all drives properly.
Access Laragon over LAN in browser as http://computername Passes and displays Laragon screen
Access Laragon over LAN in browser as 192.168.1.5 Fails: ... can't establish a connection to the server at 192.168.1.5
Access Laragon over LAN in browser as http://computername/eco1 Fails - Changes address to:
Then returns ... can't establish a connection to the server at 192.168.1.5
In httpd.conf changed <Directory /> "Allow Override to all" No Change fails to connect
Attempted to upload phpinfo() but do not not have enough privileges.
@adminnga : I think it is related to Firewall.
Thanks for picking up this thread.
I have two firewalls on each computer. One is Webroot Secure and the other is Windows defender. I also thought that either firewall could be blocking things. It was actually the first thing I thought of and I tried to see if there were issues in either with allowing things through by looking at the settings. That got no results.
So, just to be sure, on multiple occasions, after disconnecting the outside internet, I entirely shutdown Webroot and turned off Windows Defender, meaning there were no firewalls at all. After which I rebooted both computers and nothing changed.
What seems strange to me, and you would no doubt know better, is that I can connect to Laragon, although not WP, by typing the computer name into the remote computer; after which, even with firewalls in place, I get the Laragon screen on the remote computers. At the same time, if I type the address 192.168.1.5, which is the address shown in Laragon, I get the cannot connect screen in the browser.
Can you access your site using ngrok? Menu > www > Share
Since this is only used on localhost, and will never be anything other than that, in the past I never did use ngrok. However, when this problem started I tried to use it to see if I could make any kind of connection, but after checking the ngrok boxes Laragon threw, and still throws, a "Service Ngnix cannot start" error as follows:
(SSL:error:02001002:system library:fopen:No such file or
error:2006D080:Bio routines:Bio_new_file:no such file)
At this point I just went back to normal non-nginx to see if I could find a way to access.
Also, I thought that perhaps the version might have had an issue, or the install file may have had corruption, so I deleted v22.214.171.124 and installed v4.0.12_2019-128-231253. That did not help. I am still on v4.0.12 since versions are not the issue. I'll change back to the current version when the issue is solved.
Still stuck on this one. After yet another clean install, I did get it working for a short time although I am not sure why it worked. Too many changes in all the settings to be sure, but it was working - then a shutdown, went to bed, and in the morning back to the same after booting the computer.
Can you tell me if Laragon is using VirtualBox. After reinstall of Windows, for use with another program, I installed that program prior to installing Laragon a short time later.
@adminnga : Laragon does't use VirtualBox.
From the error
It happened because the right path should be:
This one is for the "who will really ever know what went on" books, but I did get it put right.
The problem, I think, was that VirtualBox was somehow grabbing (at times) the primary network adapter. When I thought this might be the problem, I attempted to change the IP address it used, but it made no difference, it still was somehow fooling about in the background and messing up any attempt to get things working (most times).
This morning, I removed it and Laragon completely. I then deleted all directories and files from the hard drives for both programs and deleted all references to them in \users. After this, I removed applicable registry entries for both and rebooted. Next was to run Windows Network Reset and again reboot. After that, all was right.
What was really odd, Leo, was that if I changed the IP address in VirtualBox the IP address that Laragon would bind to was the same as that which I entered into VirtualBox. As well, if I tried to get Laragon to use the primary network adapter it just would not, save for sometimes when it would, and this drove me crazy because it somehow kept giving the impression that VirtualBox was in the loop. It was, but wasn't supposed to be.
When I get them I always get the oddest problems.
All is well again and Laragon is back to rock and rolling! Thanks again.
@adminnga : I'm glad the you found the issue.
Laragon could detect and ignore IP from VirtualBox. However, the process take time so I removed the feature.
hello i have the same problem with Hyper-v
it use the virtual switch
i use the portable version.
if someone have a solution.